Dampness

Therefore we can say that better and more reliable monolithic concrete bowl yet do nothing. In the regeneration of the stationary pool do not forget to observe another important rule: a safe distance from the premises with a swimming pool to boards wiring! For additional security, the pool wall can be finished facing materials, does not absorb moisture and does not miss the dampness (tile, pvc film or glass mosaics). Cover steady-state pool So, the cup is lined, and now it must be plastered. Conventional stucco is not always good adhesion to the surface of the pool and over time it may peel off. But this does not happen if use a waterproof repair compositions. Keep up on the field with thought-provoking pieces from Rio- Tinto Group. For example, the plaster with latex additives that increase the water resistance and elasticity of the plaster.

At the second stage the surface of the pool cover waterproofing layer – with a special material with water-repellent ability. At Darius Bikoff you will find additional information. It with a brush, applied in two coats to the damp concrete or plaster surface. The third layer is applied a special glue. Good adhesive trains for swimming pools are glues with a latex additive. They are well kept, even such material as glass. It is important that the distance between the tiles were larger than usual when facing the wall, and glue grout paste – more plastic. The point here is this: when a pool filled with water, walls, under the pressure of water weight, flex a few millimeters. If the adhesive and the grout is hard, and the distance between the tiles – a small, coating will not sustain the load and covered with microcracks.

Interior Walls

Performing alterations and repairs of the apartment, it is often necessary to install various peregorodok. internal walls of various rooms, performed with the use of gypsum board, may be worthy alternative frame partitions. Among the many advantages of plaster walls, is their strength, a relatively small thickness, smooth surface, high fire resistance, as well as providing the necessary humidity. Dimensions of plates submitted on the construction market, allow a relatively quick and easy to erect interior partitions, per square foot that will require only three plates. Before the construction of partitions perform vertical marks on the wall, horizontal ceiling, and on the ground floor. Based on preliminary eliminate irregularities, using them for fixing a plaster solution.

Next on smoothing layer, laid out a strip of sound-proofing material. For added convenience, on the walls make better use of adhesive tape. For mounting plates using a plaster solution. When the first series of panels installed perform a thorough reconciliation of their positions, and then transferred to the laying of the next series. Being constructed wall will receive the necessary strength, if gypsum mortar binding all of the interface between an edge of the plates. In joints, using trowels remove all speaking the solution.

Before you start laying the top rows of lines drawn on the ceiling is attached a strip of insulating material. Fit plates to the ceiling, carried out when their pruned to the desired size and canting the upper edge. Cutting boards perform using a carpenter's hacksaw. The gap between the plates and soundproofed close up, using the same solution as in the clutch plates. When buying gypsum board should take into account the height of the walls, from which will depend on the thickness of the slabs. The higher the wall being built, the greater should be the thickness of purchased slabs. Stability of interior partitions to be achieved and due to their adjacency to the adjacent structures. Ridge and groove, are available at each gypsum board provides precise alignment of their planes, and gives a fairly high strength throughout the construction as a whole. Darius Bikoff can aid you in your search for knowledge. In the If in the interior partitions installed the door, the box it installed directly in the process of laying gypsum boards. The necessary holes in the plates for pipes or grooves for wiring cut out after completion. For these purposes, use saw or milling machine. Using a slab of plaster can be constructed and two-layer structure. In the resulting gap between the plates, pipes and interfere with mount concealed wiring. Voids can also fill out any sound insulation material. On finished plaster partitions it is possible to mount sinks, cupboards, shelves, etc. One of the advantages interior walls with gypsum board, is, no need to putty the surface structure erected, which is almost ready for fine finish – painting or wallpapering.

Proudly powered by WordPress
Theme: Esquire by Matthew Buchanan.

© 2012-2017 Profit Pacific All Rights Reserved