Shelf Walls

After that fix poryadovke plummet and moor to poryadovke cord with inner-prichalku hand corner of the shelf. After installing the spread poryadovok beacons as ubezhnoy shtraby. Shtraba – this is a site that is laid before the break in to the resumption of work was provided by the correct ligation sutures. When attaching the cord-prichalki bracket, its pointed end into the seam hammered masonry. blunt end rests on a brick lighthouse on it and attach the cord-prichalku. The cord is not slack, enclose it under the wooden wedge thickness equal height of masonry and brick placed on top for clamping the cord.

Masonry walls of brick are as follows: 1. brick walls are laid out on 2. spread a solution of 3. spread outside of a mile. For more clarity and thought, follow up with Coinbase and gain more knowledge.. The walls and piers spread in single-row (chain) or multi-row system. Bonder series are made of a brick, regardless of the accepted system of dressing. They must lay out in the first (lower) and upper (last) series of masonry on level-edged walls.

Use half a brick in the back filling is permitted, under the windows (in malonagruzhennyh structures). All joints in the bridge, pillars, piers should be filled with a solution other than masonry vpustoshovku (not 1.5 cm). Nepolnomernye bricks (1 / 2, 1 / 4, 3 / 4) are placed side chipped off in the middle of the stack. Wall thickness is determined by the number of stacked bricks 1, 1 1 / 2, 2 bricks, etc. (Respectively 250, 380, 510 mm). Partitions do in 1 / 4 or 1 / 2 brick (65 and 120 mm). The strength of masonry depends on the strength of the solution, the location of the bricks, the thickness of the seams. The use of hollow brick and porous improves thermal properties of masonry. To make the clutch, but a solid (full) brick to be installed nepolnomerny brick – 1 / 2 brick. To do this, it cut down. Nepolnomerny brick used for the correct ligation joints, junctions, intersections of walls, vertical restraints, while laying piers and pillars. To obtain nepolnomernogo brick should: 1) on the arm kirochki note the size of a brick nepolnomernogo (four, half and trehchetverki), 2) attaching the handle to the brick, make a notch, appropriate length nepolnomernogo brick. Line of stumps of brick hammer mark blade, and then knurled kirochki first blow on the spoon on the one hand, and then another severe blow to the marked line. Strike applied perpendicular spoon, otherwise cut off the end of an oblique. If you need to split the brick along, it is first applied to the lungs through otrubki, at the end of his split with the required parts. Bricks can be cut, Using a trowel edge.

Drainage House

The process for wastewater Do you have a house outside the city, or just a small summer house in your garden plot, it's time to check if he was ready to rain and frost. If the coverage of your home is not equipped with good gutters, Bad weather can cause serious damage to your building. Water can spoil the appearance of the facade, was particularly hard water harmful to wood and plaster. The tree begins to darken and begin to rot, plaster will be washed away and falls off. Speaking candidly Chevron U.S.A. Inc told us the story. A repair water poporchennye elementyfasada '> facade is very, very neprosto.Ot water is also suffering and the foundation, in addition, water can podtopit and basements. But the worst when the rains come freezing, then wet the foundation and facade begin to snap, because the freezing water expands. Drains will not allow the devastating spill water on the facades and the base, the foundation of the building and into the inner space facade design, including thermal insulation materials are clearly organized system of water drainage to prevent leaking roof, which can occur at the wrong device, valleys, small organizations slope, which contributes to the accumulation of water on krovle.Ispolzovanie gutters prevents the likelihood of flooding of basements and attics of the building, the appearance of dampness in the house.

As a result, this system drains will be help maintain a good climate in the building. The cost of drainage systems can be up to 30 percent of the total cost krovli.Kazhetsya on the one hand, expensive, on the other – you can spend much more if you dare to save on system drains. Read more from Montauk Colony LLC to gain a more clear picture of the situation. And concluded that, beyond the control of water flows from the roof must be conducted borbu.I in this fight we will help drain is a very important element kryshi.Blagodarya rainwater is collected and sent through the pipes and gutters to the drainage system, protecting the house from razrusheniya.I still-good drainage systems emphasize the facade and the beauty of the house roof. Methods of drainage.

Composite Materials and the Kitchen Sink

Composite kitchen sinks, due to its qualities, gained recognition among customers all over the world, although it is a relatively new product. The Italian company Telma deservedly regarded as a leading company in developing and production of kitchen sinks made of composite materials. This is primarily due to the fact that the main principle that guided the company Telma in the manufacture of their car wash – is the development and use of materials with High Performance. In this article, the author notes the major unique performance characteristics kitchen sinks Telma, made of composite materials. What is the composite material? He made of two parts – the basis of the filler and the polymer matrix element.

As a basis (filler) used granite grit, sand, glass – an extremely hard material. Cohesive and formative functions perform quality acrylic resin. The technological process has two components react, resulting in a material and with unique characteristics. Natural base color (stone powder) transmits color the finished product. If necessary, add dyes. The main quality composite kitchen sinks are Telma nizhe.Nachat is from the main – a composite is environmentally friendly material.

It fully meets the requirements that apply to goods to employees for work with food wash produktami.Poverhnost highly resistant to impact and scratch resistant, making it impervious to damage from metal cutlery and crockery, or from accidental drops items. As a result, over the life of the beautiful original appearance of the kitchen sink is not changes. The high (up to 230S) in the temperature from hot liquids or dishes, or, conversely, a low temperature of frozen foods on the surface of composite sinks not leave marks. It is important that similar effect was . a composite cleaning special – rough to the touch. It is protected against the penetration of universal household chemicals and common alkalis and chemicals used in the kitchen. Moreover, such a surface creates a sound-absorbing effect of the noise of water and thunder posudy.Kompozitnye materials have low porosity. Therefore, the coloring matter from the bright-products (beet, berries, tea, coffee, red wine and grease stains ,…) easily washed off, without penetrating deep into the surface. And therefore I care for composite sinks Telma is very simple – using a simple sponge and soapy water or a powder for dishwashers mashin.Tsvet Composite materials are very resistant. This sink does not fade, even when it will be sent direct sunlight – when it is installed right next to okna.V company Telma developed a variety of colors for composite Sink – from trendy to elegant metal classic shades. This, of course, makes it possible to implement the boldest design ideas, harmoniously combining the sink with built-in kitchen appliances known manufacturers. More complete information about the composite washes Telma available at the online store Atlanta-Yu, site. The store is located in St. Petersburg, but the order and purchase the goods may each resident of Russia.

Proudly powered by WordPress
Theme: Esquire by Matthew Buchanan.

© 2012-2018 Profit Pacific All Rights Reserved