Hongxing Mining Machinery

HX-series vertical shaft impact crusher which is high efficient equipment for making sand, is researched and developed by our company, absorbed the advanced technology rock-on-rock from America Barmac Company, and it owned advanced world standards. It has become the core equipment in sand making process. It is widely used for crushing of hard and brittle materials, such as rock, grinding material, refractory material, cement clinker, quartzite, iron ore and concrete aggregate etc; and it is highly recommended to making sand for construction and road paving.It is widely used for crushing hard and crispy materials, such as rock, grinding material, refractory material, cement clinker, quartzite, iron ore and concrete aggregate; and it is especially suitable for the sand and sandstone making for construction and road paving. Equipment well maintained is a large part to ensure the normal operation of equipment, production and product quality. For sand making machine, this criterion makes it have great significance: Firstly, regular downtime to open the sand making machine s observed door to observe the vertical shaft impact Crusher s internal wear such as barrel, cone hat, the impeller, the lining of the downstream road, circumferential shield, wear block wear after wear and tear shall promptly replace or repair, the replacement of the wear block should be replaced at the same time to ensure that the blocks weigh the same wear. It is strictly prohibited opening the door during the workings of the crusher to avoid danger observed. Found that the impeller wear timely patches to find the manufacturer replacement body.

Special attention, without the consent of the manufacturer, homemade impeller is strictly prohibited without permission.sand maker: ball mills: Secondly, the transmission of sand triangle belt tensioning size should be adjusted as appropriate to ensure that the triangular cover force uniform, two-motor drive, both sides of the triangle cover packet matching, then each group length as much as possible. Should be adjusted to make the difference between the two motor current does not exceed 15A. In addition, the sand making machine using automotive grease grade # 3 or lithium grease, 400 hours of each work by adding the right amount of grease, work 2000 hours to open the bearing spindle assembly, cleaning, general work 7200 hours and replaced with new bearings. The top of the spindle assembly bearing for the swimming side, the bottom bearing the fixed end, the assembly by hand pulling the pulley should rotate flexible. When the sand making machine is running, the device is a high speed device, you should pay special attention to production safety. Henan Hongxing Mining Machinery Co., Ltd has many years of technological power and experience accumulation of manufacturing and management of drying machines. The sand maker we researched and developed with great concentration plays an active role in the mining and ore beneficiation industry and is one of the indispensible mining crushing machinery in the mining industry. This machine has the most competitive price and the most reliable quality so that it is the top choice for the high performance crushing equipment.

Figure Out Proper Sand Washer For Your Work

Sand washer is a kind of water washing style equipment to be matched with the sand making machine and can reduce the dust and stone powder which mixes with the final sand, so sand washing machine can improve the quality of the sand. So it is for us to usually divides sand washing machine into two types, including screw sand washer and bucket-wheel sand washing machine. Bucket-wheel sand washing machine performs well with its innovative leak-proof structure and reliable gearing, which enables the machine to cope with large amount of materials, lowers the power consumption, and improves comfort. Through triangular belt, reduction gears, and slow wheel gear, electrical motor drives impeller to slowly run, slipping gravels into wash trough and washing away impurities attached on the surface. At the same time the layer of moisture will be removed from gravels to make it possible for dehydration. Later, a power flow of water is formed by continuous water supplement, taking away with it the impurities. After finishing the washing, clean gravels will be brought by impeller to blow tank. Educate yourself with thoughts from Diamonds.

Compared with screw washer, failure rate in using bucket-wheel sand sand washing machine is largely reduced since the transmission part will be separated from water and sand. Mainly characterized by simple structure, stable running state, high efficiency, and high output, screw sand washer can be often seen in construction sites, power station, and concrete plant. Materials would vertically flow into the highly-rotary impeller, and with the help of high speed centrifugal force, all materials will be crashed in to pieces around the impeller. Again and again, after many times of crashing between the impeller and enclosure, materials will be discharged through pipes, forming a closed circuit and controlling and selecting the qualified products of standard particle size after many times of circulation. In this way, it can be well applicable in washing those fine and coarse materials, especially for sand used in building industry and road.cement mill Precio: belt conveyor: But what makes the screw sand washer salient is that it is equipped with adjustable weir plate, which plays a helpful role in ensuring the high efficiency, durability, and well effect in washing and dehydration. That accounts for the stability of fine products. In addition, the well ability in treatment and convenience of repair and maintenance are all characteristics shown on sand washer screw. We can easily see it in various ore extraction industries.

Working Principle of this machine: Feed material is normally delivered between two to four feet from the feed end of the box and is subjected to an aggressive washing action resulting from the intermeshing paddle design. The paddles perform two functions: they help convey material and are the catalyst material to material on scrubbing. The material clean works uphill, between the shafts, and is discharged out the bottom of the box. Deleterious materials are absorbed into water and carried over a weir on either side of the box. The length of the washer box is dependent upon the percentage and tenacity of clay or the waste to remove.

Proudly powered by WordPress
Theme: Esquire by Matthew Buchanan.

© 2012-2018 Profit Pacific All Rights Reserved